Loading... Please wait...

FraudLabs Pro Prevents Fraud for Digital Businesses

Our Newsletter


SaniFlo SANIACCESS 3 Macerating Pump

  • SANIFLO SaniAccess Macerator
  • SANIFLO SaniAccess Installed
  • SANIFLO SaniAccess behind the wall installation view
RRP:
$980.00
Your Price:
$833.00 (You save $147.00)
SKU:
082
Brand:
Availability:
Usually ships in 3 to 5 business days!
Quantity:


Product Description

SaniFlo SANIACCESS 3 Macerating Pump

Possible connections

Toilet Sink
Shower Bathtub

Vertical and horizontal discharges: 15 Vertical ft  150 Horizontal ft

The SaniFlo SaniAccess3 is a system that is used to install a complete bathroom up to 15 feet below the sewer line, or even up to 150 feet away from a soil stack. It can handle the effluent from a toilet, sink, bathtub and shower.

The SaniFlo SaniAccess3 is simplicity itself to install; there are just four connections.

  • The SaniFlo macerator/pump is connected to the spigot of a horizontal rear discharge toilet.
  • The SaniFlo toilet tank is connected to the water supply.
  • The SaniFlo macerator/pump is connected to the small diameter discharge pipe work.
  • The SaniFlo macerator/pump is connected to the electrical supply.

The inside of the SaniFlo SaniAccess3 unit comprises of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel macerator blades and the pump.

When the flush is activated, the water flowing into the SaniFlo SaniAccess3 activates a micro switch in the pressure chamber, which in turn starts the motor.  The motor is sealed for life in an oil filled enclosure.  A common spindle/shaft drives the impeller and the macerator blades.  The moving parts therefore are kept to an absolute minimum. Water and organic waste matter enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM.  The centrifugal force causes the reduced solids to be ejected through a grill into the container where it is picked up by the impeller pump mounted beneath the motor.  The unit pumps the effluent upward to 15 feet and/or 150 feet horizontally (with gravity fall).  Once the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again.  A normal operating cycle for Saniaccess3 takes about 10 - 15 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal. 

In addition to the toilet waste, the SaniFlo SaniAccess3 will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bathtub, a shower and a urinal.  When adding a bathtub or shower, a base will have to be constructed.  This base should be made out of a 2" x 6" (minimum) or 2” x 8” (recommended) on edge, to allow for the installation of a P-trap and the required 1/4” per foot gravity flow towards the pump unit. 

The wastewater from other sanitary fixtures is discharged into the SaniFlo SaniAccess3 via two 2-inch inlets on either side of the housing.  Either one or both inlets can be used as required.  The discharge elbow on top of the unit can be turned either to the left, to the right, or towards the back, depending on the discharge installation.  A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit. 

This SaniFlo SaniAccess3 unit has been designed with a vent connection on the top of the unit.  All plumbing codes require connection to a vent system.  Please note that the vent system should be a two-way air vent.  The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems.  It is also highly recommended for the SaniFlo macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit.

Periodic maintenance can be accomplished easily without having to disconnect the unit from either the toilet or the rest of the plumbing system.  Through one service panel, a service contractor can access the electrical components as well as the level sensor mechanism of the pump.  The second service panel provides ready access to the basket area around the macerating blades for easy removal of any large objects that may have been accidentally flushed.

The SaniFlo SaniAccess3 unit must be connected to our rear discharge toilet.  This system uses much less water than a regular toilet.  Note: This toilet only works in combination with Saniflo systems.

The SaniFlo SaniAccess3 has been certified to American and Canadian Standards.  Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9. 

All items may be purchased separately.  However, the SaniFlo SaniAccess3 works as a system and therefore a toilet bowl (003 or 007), toilet tank (005) and the macerating unit (082) need to be purchased.  An optional extension pipe (030) is available for the pump to be installed behind the wall. 


Warranty Information

Saniflo offers a 2-year warranty for the pumps and a 1-year warranty for the toilet bowl and tank. The warranty starts from the date of purchase.

The warranty is voided when any foreign objects are found in the macerating unit. Pouring automobile anti-freeze, solvents paintings, acids, alkaloids, plastic bags, metal, plastic material, wood or anything that could halt, damage or corrode the unit, voids warranty. The motor is filled with oil and sealed for life at the factory; draining the oil out of the motor voids warranty as well.

Find Similar Products by Category


Write your own product review

Product Reviews

  1. Great Company and Service 5 Star Review

    Posted by on 17th Jul 2012

    The folks at SaniFloSystems are the best. I had a question about the product and they answered it immediately, and the shipping was fast.

    I would recommend this company to anyone looking to buy a SaniFlo product!



You Recently Viewed...